Intek RheoVac 950 Bedienungsanleitung

TABLE OF CONTENTSSECTION 1 GENERAL INFORMATION ... - 1 -1.1 INTRODUCTION ...

- 8 -Ñ Inspect the probe tips. Be sure wetted surfaces are clean before installing. If cleaning isneeded, use a damp cloth wetted with alcohol and wip

- 9 -Figure 5 Output Connections and Set-up

- 10 -Figure 6 Distribution Box4. Network Connection: The Ethernet connection at JP1 is an RJ-45 style jack. A 10 footEthernet Cat 5 crossover cable

- 11 -TABLE II - Optional 4-20m A C onfigurationChannelOutput Parameter1 Actual volume flow2 Total mass flow3 Water vapor flow4 Pressure5 Water vapor/

- 12 -Figure 8 Optional Transmitter BoxFigure 9 Serial Communications Interface

- 13 -Figure 10 Probe Connector AssemblyE. Cable Connection from Probe to Distribution BoxThe RheoVac probes require special connectors to be install

- 14 -SECTION 3 — OPERATION3.1 GENERAL INFORMATIONThe RheoVac system is calibrated, compensated, and linearized for a wide range of flowing mediatem

- 15 -3.4 DISPLAYThe RheoVac 950 has a 2x20 alphanumeric scroll-through display that shows seven parameters for eachprobe. The display shows Air In-l

- 16 -3.6 DATA PROCESSINGTABLE IV. Column Headings for Data Downloads and Archived Data*TimeStamp(Time ofday)ActualVolumeFlow(ACFM)Total MassFlow(lbs/

- 17 -3.7 CUSTOM SOFTWARECustom software may be developed by the user to receive and archive RheoVac data into a computersystem. The electronics has

WARRANTYIntek, Inc. warrants each RheoVac product to be free from defects inmaterial and workmanship under normal use and service, Intek'sobligat

- 18 -SECTION 4 — MAINTENANCE4.1 GENERAL MAINTENANCEPrecautions should be taken to insure proper performance of all sensors. Since the quantificati

- 19 -TABLE VI. Troubleshooting GuideMESSAGE CODEDescription/SymptomPROBABLE CAUSEACTIONMSG-0Communications notbeing received fromprobe(s)1. Improper

- 20 -TABLE VII. Troubleshooting Guide (software communication errors)OBSERVATION PROBABLE CAUSE ACTIONAppears the first time theapplication was exec

- 21 -SECTION 5 — CUSTOMER SERVICEIntek's corporate philosophy is to help solve our customers’ difficult flow measurement problems.When you pu

- 22 -SECTION 6 — CUSTOM INFORMATION6.1 UNIT IDENTIFICATIONModel no.:Serial no.: Customer identification:6.2 CONFIGURATIONThe marked (X) items denot

- A1 -I:\OFFICE\WPMANUAL\RV950 APPENDIX A3.wpd January 29, 2007APPENDIX A - RheoVac® Instrument User Interface SoftwareA.1 INTRODUCTIONUser Interface

1File transfer can also be accomplished using Windows Explorer or Network Neighborhood2 Specific network set-up at Intek may be required.- A2 -I:\OFFI

- A3 -I:\OFFICE\WPMANUAL\RV950 APPENDIX A3.wpd January 29, 2007950" network ID). The user must select the network ID from the pull down menu fol

- A4 -I:\OFFICE\WPMANUAL\RV950 APPENDIX A3.wpd January 29, 2007Figure B - User Interface Software Data Monitor FeatureFigure C - User Interface Softwa

- A5 -I:\OFFICE\WPMANUAL\RV950 APPENDIX A3.wpd January 29, 2007This screen can be divided into four parts:1. The Chart (or charts)2. The X-Axis Contro

- 1 -Figure 1 RheoVac Model 950SECTION 1 — GENERAL INFORMATION1.1 INTRODUCTIONFor the first time, all necessary properties of the gases in the conden

- A6 -I:\OFFICE\WPMANUAL\RV950 APPENDIX A3.wpd January 29, 2007to the user’s hard disk is stored in the “C:\RHEOVAC\DATA\” directory. The data is sub

I:\OFFICE\WPMANUAL\RV950 Appendix B2.wpd March 1, 2006-B1-APPENDIX B - RheoVac Model 950 NetworkingB.1 INTRODUCTIONUse these instructions when making

I:\OFFICE\WPMANUAL\RV950 Appendix B2.wpd March 1, 2006-B2-4. Networking with the RheoVac 950: If all of the items above are completed successfully, th

I:\OFFICE\WPMANUAL\RV950 Appendix B2.wpd March 1, 2006-B3-necessary. Note: The Windows installation disk may be needed as well as administratorsecuri

I:\OFFICE\WPMANUAL\RV950 Appendix B2.wpd March 1, 2006-B4-3. Check for Installed Network Components: Click the Start button and select Control Panel.R

- 2 -1.2 PRINCIPLE OF OPERATIONThe principal features of the RheoVac system are shown in Figure 1. At the heart of the RheoVacsystem is the Rheotherm

- 3 -Use reasonable care in handling the probe the sensing components are delicate. Do notbend the probes, damage the tips, or obstruct the sensing

- 4 -Figure 2 RheoVac Probe Insertion RecommendationSECTION 2 — INSTALLATION2.1 INSTALLATIONThese instructions cover installation of RheoVac instrum

- 5 -# Check installation clearance. Each transducer probe is almost 3 feet (0.9m) long and the hottap assembly is approximately 13 inches (0.33m) lo

- 6 -Figure 3Probe Stop Clamp2.3 MOUNTING HARDWARE INSTALLATIONÎ Check hardware. Verify that the probe slides through the hot tap assembly.Ï Check ins

- 7 -Figure 4 Transducer Installation Detail